Responses to “Ulefone Power2”

1. 

   09/23/2013
   

    

   djukas on 08/22/2019 @ 9:10 am

   Mnogo hvala mom prijatelju Fici sto je nasao i postavio ovaj rom

   Log in to reply.
2. 

   01/14/2014
   

    

   file015 on 08/22/2019 @ 9:37 am

   

    

   Log in to reply.
3. 

   01/14/2014
   

    

   file015 on 09/04/2019 @ 8:35 am

   If You Have It In Your Power 2
   GQ3035JF5 Ulefone G06 20170715-sign user.tar
   You can flash
   GQ3035JF5 Ulefone V19 20170811 user.tar
   with SP Flash Tool v5.1824 Win by inserting the skater file from GQ3035JF5 Ulefone G06 20170715-sign user.tar into SP Flash Tool v5.1824 Win after all but the system is added, and by double-clicking on the system you add the system path of GQ3035JF5 Ulefone V19 20170811 user. tar. Then download or update the firmware. Turn off the phone, turn it on
     + volume and connect your phone to usb laptops or desktops. When the red progress bar goes, you release the buttons. It's all over in a few minutes. Your data stays tuned as you did before you just got a new system. If you have questions I'm here.
   Good luck.

   PS. My English is bad, I hope you understand everything.

   Log in to reply.
4. 

   05/09/2019
   

    

   cbvc on 01/31/2021 @ 2:05 pm

   Здравствуйте, можете по русски написать как перепрошить с одной прошивки на другую . А то программа выдает ошибку ( please download signed image(md1img-verified.img) or disable verified boot ).

   Log in to reply.
   • 

     01/14/2014
     

      

     file015 on 01/31/2021 @ 5:38 pm

     G06 20170715 to V19 20170811 
5. 

   12/07/2021
   

    

   apxub13.2018 on 12/07/2021 @ 10:31 pm

   hello! i had G06, made factory data reset, then turn on usb debug+oem unlock, then my pc see power2 as "MediaTek DA USB VCOM Port".

   Then i made G06 20170715 to V19 20170811 via your instruction with "update firmware" option inside spflashtool. Red status bar got 100% very fast, then after 3-4min nothing happen at all.

   After all that phone is not reacting on buttons at all and stays black, even charging is not going via 220v.

   WHAT TO DO ?

    

   Log in to reply.
6. 

   01/14/2014
   

    

   file015 on 12/18/2021 @ 8:45 am

   I'm sure you didn't do something right. Your USB cable may not be good, and I don't have that phone anymore to check where you went wrong. The 100% method has been tested not just once but at least 20 times. Make sure the phone has an unlocked boot loader.

   1.   Once you get the code you can enable the Developer Option
   To Enable the Developer Option, Go to your Settings -> About -> Software Information -> More -> Now Tap on the Build Number 7-8 Times until you see a toast message “Developer option enabled"build
   Go back to settings -> Now you need to enable the OEM Unlock by going to Settings -> Developer Option and Enable OEM Unlock and USB Debugging  OEM Unlock

       Download and Extract the Downloaded ADB fastboot Zip file on your PC

   2.  Now connect your phone to Computer using USB Cable.
   When you connect your Phone to Computer, please wait until all the drivers get installed.ADB Folder
   In your ADB fastboot folder open a command prompt window by pressing Shift Key + Right Mouse Click 
   Now type the command in your command window

   komanda:   adb devices

   If you see a pop up to allow USB Debugging on your phone, Click OK
   Now type the command below to reboot your phone to bootloader

   comand:   adb reboot bootloader

   Once your phone reboot into bootloader, make sure your phone shows the bootloader locked and then type the command below to make sure fastboot drivers are installed properly.

   komanda:   fastboot devices

   This command will list the connected devices. If your phones serial number shows up you are good to go and may continue. If the phone is NOT listed this indicates that your drivers are not installed correctly. In order for you to continue you must fix your drivers so that your phone is listed under fastboot devices.
   If the phone has been recognized by the command above, proceed to unlocking the bootloader with the following command:
   Remember that this step will wipe EVERYTHING off the phone 

   command:   fastboot oem unlock
              fastboot oem lock

              fastboot oem disable_dm_verity

              fastboot oem enable_dm_verity

              or:

              adb disable-verity 

              adb enable-verity

   After the above command has finished executing, run the following

   komanda:   fastboot reboot

   The phone will reboot. Wait until the phone has fully booted up into android, and enjoy!
   I hope you have successfully Unlocked Bootloader on your Mediatek phone.

   Log in to reply.