• Title: TWRP 3.1.1 (BL7000)
  • Listed: 09/29/2017 6:43 pm
  • ROM Version: TWRP 3.1.1
  • You must be logged for ROM download.

Overall Rating : 4

4089 total views, 7 today

4 Total favorites


TWRP 3.1.1 (BL7000)

Author adMember Info


DOOGEE BL7000 TWRP 3.1.1

Обязательно разблокируйте загрузчик !!!

Восстановление основано на прошивке ядра Android 7.0 версии DOOGEE-BL7000-Android7.0-20170904


ATTENTION!! After the installation of the recovery, under the condition of allowing changes in the system, it is necessary to install SuperSU, otherwise the system will not boot .

1. To install TWRP, you must unblock the boot loader. As a result of unlocking you will receive a completely clean phone: all user data and programs will be erased! In the "Settings" menu of the smartphone, activate the "For Developers" menu (usually by repeatedly clicking on the build number in the "About phone" tab) and select from the menu "Enable Factory Unlock" and "enable USB debugging". Switch off the machine.

2. Put the device in the "fastboot" mode by pressing the key combination up and power off from the turned off state, selecting from the appeared text menu bootloader option "fastboot".

3. Connect the smartphone cable to the USB port of your computer (in the Device Manager, the Android ADB Interface device should appear), set the required ADB drivers and unpack the archive into the ADB folder, which should be in the root of the C drive

4. Run the command line and type in it

cd c: ADB

5.After enter enter the command:

fastboot devices

if everything is installed and connected correctly, as a result of the command you will have to get the output of your smartphone's line:

0123456789ABCDEF fastboot

6. Enter the command to unlock the bootloader:

fastboot oem unlock

On the smartphone screen, you will be prompted to confirm the unlock by pressing the volume up. Press the volume up.

7. Reboot your smartphone using the command fastboot reboot

Wait for the system to boot up, then turn off the smartphone and again call the "fastboot" mode by pressing the key combination up and down power, selecting from the appeared text menu bootloader option "fastboot".

8. Copy the image twrp_bl7000.img to the folder with ADB-utilities.

At the command prompt, type:

fastboot flash recovery twrp_bl7000.img

9. Turn off the power of the smartphone while holding the power button for a long time.

Call the loader menu by pressing the volume up keys and power, selecting from the appeared text menu bootloader option Recovery and log in TWRP.

Install SuperSU and reboot into the system (SuperSU installation options can be installed from an external card, or after format via a usb cord using pc)

If twrp at startup asks for a key (password), it means that the data partition is encrypted. It is treated by formatting the Data section

※Please make a backup of your device before installing or updating ROM

Donate with YANDEX to kentst

11 Responses to“TWRP 3.1.1 (BL7000)”

  1. 04/04/2016

    i tried to root my BL7000, but could not,
    and my BL7000 is now in bootloop.
    Orange State
    Your device has been unlocked and can't be trusted
    Your device will boot in 5 seconds
  2. OraNeedRom



    I need the stock ROM from Doogee BL7000 or a readback from a ROM. Who can help me?

  3. 10/04/2017

    Czech Republic

    yeah my phone is now also stuck in bootloop, might need the official rom, please help


  4. tkl.europe



    I need the official Rom too . After i had rooted my Phone , the IMEI was dissapeared , so i would flash back my Backup made with TWRP to restore the nvram . TWRP was unable to write this back because the system was write protected  and after triying to restore the Backup with TWRP  , i´m in bootloop . 

  5. 08/17/2017

    Russian Federation


  6. 10/21/2017


    I have the same situation….

  7. 10/24/2017


    I flashed twrp but when entering Recovery, dead droid image appears with "No command" text written

  8. 10/27/2017


    I habe lost the IMEIs of ma BL7000, too. and the same problem.

    After bootloop and many other crazy things on my BL7000, now i have installt twrp recovery and cwm recovery. and both are working.

    With the rom manager app i was able to reactivate cwm recovery in chines. 

    now i´m back in the cwm recovery in chines language, but when i want to swap and reload the eMMC i get the info: cwm emmc is busy can´t format, please retry.

    I have twrp root, but all tools to restore the IMEI numbers need the root of cwm. I have busybox installt and root checker tells me android have root.

    to set the IMEIs by Droid tools v2.5.3 to set the IMEIs by Droid tools v2.5.3 root is not possible, but needet to set the IMEIs.

  9. 04/05/2018


    This bootloader sucks, i lose my IMEI too. Do not donwload!!

    • 04/05/2013

      Czech Republic


      Excuse me for "tool hero", it does not work on this phone, but installation of TWRP and ROOT works.

  10. 04/05/2013

    Czech Republic

    Thank you for this work!
    I struggled, I drooled but I arrived install TWRP and ROOT on Doogee bl7000.
    I am not a very great specialist, but I do not like losing.
    Respect instructions to the letter, do not skip any line and it works.
    I tested different ROMs, I lost the camera, but I installed ROM from here:

    I did everything on this ROM, lost nothing.

    Very important, do not boot after installing TWRP, first install ROOT from External SD Card.

Leave a Reply

You must be logged in to post a comment.